Can I Install A Bath Tub Myself?
Can I Install A Bath Tub Myself?
Blog Article
The article author is making a few good observations on the subject of How to Install a Bathtub Yourself in general in this article below.
Mounting a bathtub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably tough project. If the old bathtub is readily easily accessible, the project can relocate speedily; if you need to open up a wall to get rid of the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as set in the new one. See to it you have qualified yourself for the work and are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your restroom if you have currently bought a new tub and also do not need to alter the plan of your previous water pipes.
Your tools as well as product list should make up the following:
Preparing for the Installation
First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water system. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the limited access that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the new faucets, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub till the spirit level reviews level.
To install taps, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water as well as check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as likewise inspect the overflow outlet as well as the normal electrical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the maker's instruction manual. Tiling and sealing around the bath tub must wait up until the bath tub has actually been utilized a minimum of once as this will settle it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washers are in place between the tap and also the sink. Safeguard the faucet in place with the producer offered backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind should be attached to the faucet ends first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, causing problems with wetness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and installations. They are offered in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can break rather early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly readily available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a reader on How to Install a Bathtub, I assumed sharing that blog post was a great idea. Appreciated our write-up? Please share it. Help other people locate it. Thank-you for going through it.
Click
Report this page